Calculated-industries 4095-C Pocket Reference Guide Bedienungsanleitung

Pocket RefeRence Guide — 17Sixth press of  : (Fractionalmode) FRAC Std.  FRAC COnSt. (repeats options) FRAC Std. Seventh press of  : (Mat

Using M+KEYSTROKE DISPLAY    M+ 355. M    M+ 255. M7     (M-) M- 745. M  TTL – 135. M AVG – 45. M CNT 3. M ; 

Pocket RefeRence Guide — 21KEYSTROKE DISPLAY  0. MATL PL AStIC    (PipeType) TYPE 80 PLAStICPipe Size KeyWhen you have chosen a Pipe

elbow ttings can have a different Take-Out calculation from the eld cut variants.This function toggles the Elbow types between the following options

Pocket RefeRence Guide — 251.EnterOffset:1 6   OFST 16 INCH2.EnterRun:2 7   RUN 27 INCH3.Findthepipelength: TRAV 31-3/8 INCH4.

Pocket RefeRence Guide — 27Note: ToreturntheWelder’sGaptothedefault1/8”,press toresetyourcalculatorbacktodefaultvalues.Rolling

Pocket RefeRence Guide — 291.EnterPipeSize:6   STD SIZE 6 INCH2.ChangethedefaultWelder’sGapfrom1/8”to3/32”:   2   * GAP

Pocket RefeRence Guide — 31Calculate Take-Out and Butt Weld Elbow Cut MarksThe Take-Out function can be used to quickly solve a Take-Out and butt wel

Pocket RefeRence Guide — 336.Enter0forWelder’sGap:   (Welder'sGap) GAP 0 INCH7.Findthepipecutlength: TRAV 14-1/8 INCH CU

Pocket RefeRence Guide — 352.ChoosethePipeType:   (PipeType) TYPE 5 S.StEEL3.EnterthePipeSize:  5 SIZE 6 INCH4.Findtheweightofo

Pocket RefeRence Guide — 1Designing and building new calculators like the Pipe Trades Pro™ Advanced Pipe Trades Math Calculator and the PlumbingCalc P

anyoperatorkeyispressed.Forexample,30°89’enteredwillbecorrectedanddis-playedat31°29’0”or31.48°.Trigonometric FunctionsTrigonometri

Note:Pleaseusecautionwhendisposingofyouroldbatteries,astheycontainhazardouschemicals.Replacement batteries are available at most discoun

This equipment has been certied to complywith the limits for a Class B computing device,pursuant to Subpart J of Part 15 of FCC rules.Software copyri

For more information regarding Warranty, Repair and Return, see the full User's Guide.

Pocket RefeRence Guide — 3 Table of conTenTsGETTING STARTED ... 5KEY DEFINITIONS ...

Pocket RefeRence Guide — 5 GeTTinG sTarTedYou may want to practice getting a feel for your calculator keys by reading through the key denitions and l

Pocket RefeRence Guide — 7fractionalanddecimalinches. Fraction Bar – Used to enter fractions. Fractions can be entered as proper (1/2, 1/8, 1/16)

Pocket RefeRence Guide — 9Circle Key Circle – Enters diameter and calculates circle area and circumference.Trigonometric Keys  Sine – Finds the si

 Take-Out (T.O./Arc) – Used to enter or solve tting Take-Outs when calculating pipe cut lengths. Calculates inner, center, and outer arc lengths f

Pocket RefeRence Guide — 13Miscellaneous Functions  Open parenthesis key. Close parenthesis key. Xy – Enters an exponential value other than x2

Pocket RefeRence Guide — 15Enter the Preference Mode by pressing  (Prefs). Access each category by pressing the  key until you reach the desir